How "handy" are you?
 

On a scale of 1 to 10?

I admit I am not much of a handyman. I'd rate myself a 2. I just changed some light fixtures in our laundry room and it took me about an hour and a half for two fixtures. I should have hired an electrician. At least they look good and work right.

I'm better out-doors in the yard and garden. I'd give myself a 9 for outside work.

I'd say I'm about a 6. I do very well with Carpentry and Electrical, but I'm useless with plumbing and Automotive.

I've build a shed and a deck without much problem. But on the weekend, I tried to change a washer and took an hour.

Just above average, about 6

I am an 11 if by handy you mean handjobs :2 cents:

I'm a 10 !!

A 1. It's hard for me to assemble furniture! I can't do it. A few times I built it wrong and someone had to help me :(

I would rate myself at a 7 or 8. As long as I have some kind of instructions for a project that I've never done before, I can do it.

Plus, it's an excuse to buy more tools.

Bulit this last year
http://www.whatsdone.com/pokertable/images/036.JPG

Those instructions are hard to follow! It's just a bunch of illustrations with 20 screws listed saying 20x 10x 5x and all the screws look the damn same. And all the boards look the same, how can you tell which is which! Yes there are pics but sometimes all the boards look the same!

I hear ya. I used to have problems with Ikea stuff even! :1orglaugh

9 3/4 but that is because I am missing the first joint of my left index finger.
I may of not build a cool table but does a APU for a DC-10 count?

NosMo

Even just doing some reverse engineering on things works out usually, or just a pic of the final product. And then sometimes when the instructions just stop being useful, you use power tools to make it fit. Sometimes, it just takes a little jimmy rig. :thumbsup

1, perhaps 2 :Oh crap

9 to a 10. Not much I cant do if I put my mind to it. Ran a bodyshop, have restored 15 Studebakers. Built additions on houses, worked in construction, father owned a heating and cooling biz that I worked fulltime for, then part time for for years. Here is one of my babies. It stays up in PA at my parents its it cozy garage. Full off body restore by me, all body work by me, all paint by me. Only thing outsourced there was any chrome work, and upholstery work. Oh and had engine rebuilt too, though Ive done that in the past.

http://www.whatstaboo.com/HPIM0205s.jpg

http://www.whatstaboo.com/HPIM0204s.jpg

What is that? Is it a poker table?

Ikea instructions has fucken stickfigures on it! There's a drawing on it of a stickfiguring calling ikea for help wtf

IKEA is actually the HARDEST furniture to assemble I think. Their instructions have no words because IKEA is cheap and wants to use the same instructions for every country, it's not even written. It's all illustrations and stickfigures.

I think I'm pretty handy for a girl. I actually have power tools.

My exhusband didn't even own a screwdriver.

id say im a 9 or 10.

safe to say 9, never had to hire anyone.

That's a monster project!

I just finished this bar a couple of weeks ago:

http://www.stupidcoeds.com/gfy/bar3.jpg

http://www.stupidcoeds.com/gfy/bar6.jpg

http://www.stupidcoeds.com/gfy/bar13.jpg

http://www.stupidcoeds.com/gfy/bar14.jpg

more pics here: fucking-around-and-business-discussion/796611-am-build-bar-pictures-build.html

9. I hate plumbing, but can do it if necessary.

You are very handy.

Everyone look at this thread I made back in December asking for help assemblign a table! I even included a picture! I tried for 3 hours getting the screw in and I could not do it!! http://www.gofuckyourself.com/showthread.php?t=790635

The next day I had a guy over I hired to move some boxes for me. I asked him to do it for me and he got it in within 3 minutes! I guess I just didn't position the screw in right! The angle was off.

Hey, I was going to ask you about that. For the sink you put in the bar top, did you plumb that into your house, or does it just drain into a bucket or something?

A bar is going to be one of the first projects in my new house, so I'm just trying to do some recon.

Bump it up

If you are doing a new build (house) by all means add it to the plumbing. Unfortunatly for this one a drain would have meant major construction. I would have had to plumb it down to the first floor kitchen drain and then behind the cabinents. For this one it ended up being the dreaded bucket :disgust They are not terrible, you just have to keep an eye on them.

If you are building in a already constructed house, I have ran them through the floor and into the basement sump pump.

I'm a 1 and thats pushing it

Diagnosed and repaired my dishwasher issue a couple weeks ago.

Hmmm I girl with power tools....drool. Well I am out...


NosMo

Probably 8.5

My basement was a typical 1500 sq ft box, just the concrete walls, no electrics, no ceiling or floor.

Now its a fully completed content studio with changing room and gear storage, 4 studio sets, built in 9 ft backdrop hangers, recessed lighting, sound system. Took 3 months, no other help.

I didnt skip the planning permission or inspections, so its gotta be alright lol

Probably about a 7 to 8.

On average, I'm a 8-9. I love buiding shit and fixing things. Wood, electrics, auto, whatever. I've always been able to just look at something and tell you how it works, or why it doesn't.

I'm an 8

Ya, the house is already to close to completion, so adding the plumbing now is not a possiblity. I think I'm going to just skip the sink on this one. I want to make an "L" shaped bar, but it seems like it would be a pain in the ass. I want to stain it dark so I don't have to use really expensive wood, but so it still looks nice. I just don't want to stain it while it's on top of the carpet, so I might rethink my plan.

I might hit you up again for some advice once I get into it, if you don't mind.

I'm about 8-9 .. can do alot of stuff..

I'd say 8.5-9

Some of my previous occupations:
- automotive refinisher (body work, prep & paint)
- frame/structural and mold fabrication (composites, hybrids, fiberglass, various metals and plastic). Includes automobile replication.
- construction (framer, brick layer, tile setter, finishing, plumbing, electrical etc et cetera. Uh, I'm Italian.)
- landscaping


About the only thing I never really got in to, because it was a no no in auto refinishing, is auto mechanic (engine work),. Grease and paint do not mix.

No problem - as for staining, do it like I did - cut all of the pieces outside and stain them there, then assemble it inside. An air nailer works best for tacking the panels onto the frame but screws are fine also.

I was 2-3 a year and a half ago... Id say 5 now

I'm very handy at what I do.

Which is to whine and look pathetic until someone else does it for me.